|
Yet
again Duolabs strike
back with another
ground breaking device.
The CAS INTERFACE
3.
In
a single product,
the CAS Interface
3, combines all the
superb features of
the CAS Interface
2, its Add-On Board
plus many additional
options.
This new release offers
very advanced technical
features. Unlike the
CAS Interface 2, the
CAS Interface 3 can
fully manage PCMCIA
connectors and easily
connect external additional
modules.
However, the most
interesting feature
is the possibility
of being able to emulate
the PCMCIA port of
a Common Interface
(EN50221) receiver
and thus use a Cam
directly as if it
were inserted in a
receiver.
Consequently the CAS
Interface 3 can also
be used by professionals
to test a CAM (Conditional
Access Module) without
inserting it in a
receiver.
CAS Interface 3 also
enables users to manage
and program several
types of SmartCard,
which includes both
current ones and those
yet to be developed.
Therefore the CAS
Interface 3 can be
regarded as a multifunction
programmer suitable
for the management
of J-Tag, ISP, I2C,
etc., through a USB
port.
All
features are explained
in the User
Manual
available to download
from our site.
The
CAS Interface 3 will
be available through
our official distributors
and via our online
shop.
The
Kit supplied
with CAS Interface
3 comprises of:
•
1 CAS Interface 3
device
•
1 20-Pin female cable,
length 30 cm
•
1 J-Card
•
1 Dummy Card
Technical
The main features
of this great device
are as follows:
USB
Full Speed connection
at 12 Mbit
RS-232 Serial Connection
20 Pin External Connector
Internal Clock Speed
48Mhz
No need for external
power supply
Full PCMCIA connector
support
Full support for next
generation Wireless
devices
CAS Studio user friendly
GUI
On
the ground features:
-
Common Access
Modules (CAM):
•
Magic Cam,
Matrix Cam, Matrix
Revolution, Matrix
Reloaded, Matrix Reborn,
and all CAMs based
on SIDSA chipsets,
which can be managed
directly by means
of a PCMCIA connector.
For a full list of
supported modules,
open the Graphics
Menu of Cas Studio.
Remember to download
the latest release
from our web site.
Thanks to the High
Speed internal clock
Cas Interface 3 is
around 4 times faster
than Cas Interface
2. Most of software
routines for Flash
writing have been
rewritten.
•
Joker Cam,
Zeta Cam and substantially
all CAM modules based
on NEOTION chipsets.
These modules can
be programmed and
repaired using a J-Card.
For a full list of
supported modules,
open the Graphics
Menu of Cas Studio.
Remember to download
the latest release
from www.duolabs.com.
•
Dragon Cam;
it is possible to
program any version
by inserting the Dragon
Cam into Cas Interface
3 and using a Dummy
Card. This mode eliminates
the need of inserting
the Dragon Cam into
a receiver, which
can sometimes damage
the CAMs besides being
unpractical. It is
also possible to repair
faulty Dragon Cams
if they fail to initialize
due to a faulty Flash
Memory. To do so,
it is sufficient to
open the module and
connect a few wires,
following a procedure
that can be easily
implemented even by
less expert users.
Special thanks goes
to Dream Multimedia
for their support
and patience.
•
X-Cam, with
ANGEL and ORION chipsets,
standard and premium
version. It is possible
to program any version
by inserting the X-Cam
into Cas Interface
3 and using a Dummy
Card. This mode eliminates
the need of inserting
the X-Cam into the
receiver, which can
sometimes damage the
CAMs besides being
unpractical. It is
also possible to repair
faulty X-Cams if they
fail to initialize
due to a faulty Flash
Memory. In this case
it is necessary to
open the module and
connect a few wires,
following a procedure
that can be easily
implemented even by
less expert users.
Special thanks goes
to X-Crypt for their
support.
-
Smartcard programming.
This feature is very
important for all
those who wants to
program a Smartcard
based on PIC microcontroller
or Atmel microcontroller.
The full list of Smartcard
can be viewed directly
from the graphical
menu of Cas Studio.
More... All the OS
cased cards like Titanium
Card, OPOS Card, Knotcard
and more can be programmed
without any problem
throught the USB port.
All future Smartcard
can be supported thanks
to the great flexibility
of Cas Interface 3.
Dragon Card Loader
can be fixed if corrupted
by the special repair
function.
-
RS-232 Phoenix
Smartmouse emulation.
This emulation can
be done through the
RS-232 serial port.
No matter what's the
clock speed for the
Smartcard. You can
either choose 3,58/3,68/4,00/6,00
Mhz. This great feature
is given by the total
flexibility of the
internal programmable
clock generator.
-
DreamBox 56xx and
7000 series boot repairing
function.
If your DreamBox wil
not reboot due to
a faulty flash the
CAS Interface 3 will
solve your problem
without the need for
any special cables
or hard soldering.
-
Sidsa embedded
chip Set-Top-Boxes
programming.
Program the Sidsa
CA embedded module.
This most works like
Cam programming feature.
No need for special
cables or special
connectors.
Support receivers
are Xtreme, Manhattan,
Nextwave 2500.
-
Cam Explorer.
This is a real cool
feature which allows
the user to insert
any Cam in the PCMCIA
connector and browse
the content of you
Cam. This acts like
a real Common Interface
Set Top Box. It gives
you the possibility
to get into the menus
and at the same time
use all the remote
controller features.
-
Various Utilities.
Various PC utilities
are included in Cas
Studio. All those
tools are free of
charge and can be
freely used. Duolabs
made them to give
the user the possibility
to enjoy other
*
Sim Editor.
This software allows
you to edit your GSM
smartcard. Save/edit
phonebook, SMS and
Smartcard files.
* Wincrypt.
This software allows
you to encrypt and
decrypt your files
and folders using
as 3DES key your GSM
Smartcard. This software
works pretty much
as Winzip but the
encryption is secured
by a secret key in
your GSM Smartcard.
And
there we go with our
photo gallery:
Cas Interface 3.
Metal Case for Cam.
Cam Explorer Gallery
|
